FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
Store Updates
The Moose Racing Handlebar Riser Kit (0602-0790) is an adjustable, CNC-machined billet aluminum spacer system engineered for 2016–2023 KTM and Husqvarna enduro, dual-sport, and off-road motorcycles equipped with rubber-damped handlebar mounts. Taller riders and off-road racers spending extended hours standing on the footpegs frequently experience lower back strain, shoulder fatigue, and reduced front-end leverage when running standard low handlebar heights.
Precision-machined in the USA from 6061-T6 billet aluminum, the0602-0790 kit installs directly between the rubber-mounted lower handlebar perches and the top triple clamp. Interlocking spacer blocks allow riders to raise handlebar height from 5 mm up to 30 mm (1-3/16") without replacing their stock 1-1/8" (28.6 mm) tapered handlebars or OEM clamps. The kit includes multiple lengths of high-tensile M10-1.5 socket-head mounting bolts and an 8 mm hex wrench to ensure proper thread engagement across different spacer stack configurations.
Adjustable 5 mm – 30 mm Rise: Interlocking billet spacer blocks allow custom bar height adjustments up to 30 mm (1-3/16") to improve standing ergonomics and control leverage.
6061-T6 Billet Aluminum Construction: CNC-machined from aircraft-grade aluminum for high torsional rigidity and zero bar-mount flex under hard trail impacts.
Interlocking Alignment Geometry: Machined step-and-pocket bosses lock stacked spacers squarely together and into the OEM lower bar perches to eliminate twisting.
Preserves OEM Handlebars & Rubber Damping: Installs beneath the factory lower bar perches, retaining full compatibility with stock 1-1/8" (28.6 mm) oversized bars and OEM rubber isolation cones.
Multi-Length Hardware Included: Ships with both 40 mm and 55 mm high-tensile M10-1.5 socket-head mounting bolts to match varying riser stack heights.
Made in the USA: Engineered and CNC-machined in the United States.
4x CNC-Machined 6061-T6 Billet Aluminum Interlocking Riser Spacers (5 mm to 30 mm stackable configuration)
6x M10-1.5 x 40 mm High-Tensile Socket-Head Mounting Bolts
2x M10-1.5 x 55 mm High-Tensile Socket-Head Mounting Bolts
1x 8 mm Hex / Allen Installation Wrench
1x Installation Instruction Sheet
Generation Incompatibility Warning: Engineered specifically for the2016–2023 rubber-mounted round/oblong lower bar perch generation.
DoesNOT fit 2024+ KTM/Husqvarna/GASGAS enduro models with updated cast triple clamps (requires Moose Racing0602-1518 / EE23-1024).
DoesNOT fit 2023+ SX/XC/TC/FC/TX/FX or Hard Enduro models with updated CNC billet triple clamps (requires Moose Racing0602-1422 / EE23-1023).
DoesNOT fit 2000–2015 KTM or 2014–2015 Husqvarna models with rigid square-base bar mounts (requires Moose Racing0602-0755 / EE23-002).
Part Number Cross-Reference: Cross-references Enduro Engineering Manufacturer Part Number23-016.
Installation Without Removing Handlebars: You do not need to remove your handlebars, grips, or control perches to install this riser kit. Drape a clean shop towel over the front fender and fuel tank, then use aT-45 Torx socket (or 17 mm socket, depending on model year) from underneath the top triple clamp to remove the two lower bar-mount bolts. Lift the handlebars and lower perches upward as a single unit, seat the selected interlocking spacer blocks onto the rubber damper washers, and retain the thick factory steel washers beneath the heads of the new mounting bolts.
Bolt Length Selection & Blind-Hole Bottoming Check: Match the supplied M10-1.5 bolts carefully to your chosen spacer stack height:
5 mm – 15 mm Rise: Use the40 mm socket-head bolts.
20 mm – 30 mm Rise: Use the55 mm socket-head bolts.
Always thread each bolt into the lower bar perch by hand before final tightening to verify at least 10–12 mm of thread engagement without bottoming out inside the blind perch threads. Apply a drop of medium-strength (blue) threadlocker to the bolt threads and torque from underneath using the supplied 8 mm hex key to KTM/Husqvarna factory specification (29.5 lb-ft / 40 Nm).
Maintaining Rubber Cone Alignment: On 2016–2023 KTM and Husqvarna triple clamps, the lower bar mounts sit inside tapered rubber damping cones pressed into the top clamp. Keep the top bar clamp bolted across both perches while tightening from underneath so the left and right lower perches remain parallel and do not twist or pinch the rubber isolation cones.
Cockpit Reach & Full-Lock Cable Clearance: Because the steering stem is raked backward at roughly 26 degrees, raising the handlebars vertically along the fork axis also moves the grips slightly rearward toward the rider. If the cockpit feels cramped at 20 mm or 30 mm of rise, rotate the reversible OEM lower bar perches 180 degrees into the forward mounting position on the triple clamp. Before riding, lift the front wheel off the ground and turn the bars from full left lock to full right lock to verify that the front brake hose, hydraulic clutch line, throttle cables, and kill-switch wiring have adequate slack without binding.

Part Number: 0602-0790
If you have any questions or need help finding what you need for your motorcycle or your next adventure please reach out:
EMAIL US AT tmbrmoto@tmbrmoto.com- OR CALL - 208-254-2044
Our shop is temporarily closed. Check back soon — we'll be back before the next ride.