FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
Store Updates
The Moose Racing Handlebar Riser Kit (0602-1422) is an adjustable, CNC-machined billet aluminum spacer system engineered for 2023+ KTM, Husqvarna, and GASGAS motorcycles equipped with CNC-machined billet triple clamps. Taller riders and off-road racers spending extended periods standing on the footpegs frequently experience lower back fatigue, shoulder tension, and reduced front-end leverage when running standard bar heights.
Precision-machined in the USA from 6061-T6 billet aluminum, the 0602-1422 kit mounts directly between the top triple clamp and the factory lower handlebar perches. Interlocking 5 mm and 15 mm spacer blocks allow riders to configure handlebar rise at 5 mm, 15 mm, or 20 mm while retaining their stock 1-1/8" (28.6 mm) tapered handlebars and OEM clamps. The kit includes three matched sets of high-tensile socket-head mounting bolts (40 mm, 50 mm, and 60 mm) and an installation hex wrench to guarantee exact thread engagement for every spacer stack height.
Adjustable 5 mm, 15 mm, or 20 mm Rise: Stackable 5 mm and 15 mm spacers provide three distinct bar height options to optimize standing ergonomics and rider leverage.
6061-T6 Billet Aluminum Construction: CNC-machined from aircraft-grade aluminum for high torsional rigidity and zero bar-mount flex under hard landings or impacts.
Interlocking Alignment Geometry: Precision-stepped bosses lock stacked spacers squarely together and into the lower bar perches to eliminate twisting.
Retains Stock Handlebars & Perches: Installs beneath the factory lower handlebar mounts, preserving full compatibility with OEM 1-1/8" (28.6 mm) oversized handlebars and controls.
Three Bolt Lengths Included: Ships with 40 mm, 50 mm, and 60 mm high-tensile M10 socket-head mounting bolts so thread engagement matches the selected riser height.
Made in the USA: Engineered and CNC-machined in the United States.
1x Set of CNC-Machined 6061-T6 Billet Aluminum Interlocking Riser Spacers (5 mm & 15 mm blocks for up to 20 mm rise)
2x M10 x 40 mm High-Tensile Hex-Socket Mounting Bolts (for 5 mm rise)
2x M10 x 50 mm High-Tensile Hex-Socket Mounting Bolts (for 15 mm rise)
2x M10 x 60 mm High-Tensile Hex-Socket Mounting Bolts (for 20 mm stacked rise)
1x Hex / Allen Installation Wrench
1x Installation Instruction Sheet
0602-1518 (Enduro Engineering23-1024).
Installation Without Unbolting Controls: You do not need to remove your handlebars, grips, or control perches to install this riser kit. Protect the front fender and fuel tank with a clean shop towel, then use aT-45 Torx socket from underneath the top triple clamp to remove the two factory bar-mount bolts. Lift the handlebars and lower perches upward as a single assembly, insert the desired interlocking spacer combination, and reuse the thick factory steel washers beneath the heads of the new mounting bolts.
Strict Bolt-to-Spacer Matching & Threadlocker Protocol: Select the supplied bolt length that corresponds directly to your chosen riser stack height:
5 mm Rise:Use the40 mm bolts.
15 mm Rise:Use the50 mm bolts.
20 mm Rise (5 mm + 15 mm stacked):Use the60 mm bolts.
Never install a longer bolt with a shorter spacer configuration—the fastener will bottom out inside the blind threads of the lower bar perch before clamping it down against the triple clamp. Apply a drop of medium-strength (blue) threadlocker to the bolt threads before installation.
Preventing Spacer Rotation During Final Torque: When tightening the mounting bolts from underneath the top triple clamp, rotational friction from the bolt head can cause the lower bar perch and spacer stack to twist slightly out of alignment. Hold the lower bar perch squarely with an open-end wrench (or keep the top bar clamp bolted across both perches) while torquing the M10 mounting bolts from underneath to KTM/Husqvarna factory specification (29.5 lb-ft / 40 Nm).
Cockpit Reach & Full-Lock Clearance Check: Because the steering stem is raked backward at roughly 26 degrees, raising the handlebars vertically along the fork axis also shifts the grips slightly rearward toward the rider. If the cockpit feels too cramped at a 15 mm or 20 mm rise, rotate the reversible OEM lower bar perches 180 degrees into the forward mounting holes on the triple clamp. Before riding, elevate the front wheel and turn the bars from full left lock to full right lock to verify that the front brake line, hydraulic clutch hose, and throttle/switch wiring have adequate slack without binding.

Part Number: 0602-1422
If you have any questions or need help finding what you need for your motorcycle or your next adventure please reach out:
EMAIL US AT tmbrmoto@tmbrmoto.com- OR CALL - 208-254-2044
Our shop is temporarily closed. Check back soon — we'll be back before the next ride.