FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
Store Updates
The Moose Racing Handlebar Riser Kit (0602-1518) is an adjustable, CNC-machined billet aluminum spacer system engineered for 2024+ KTM, Husqvarna, and GASGAS motorcycles equipped with updated OEM cast/forged triple clamps. Taller riders and off-road racers spending extended hours standing on the footpegs often experience lower back strain, shoulder fatigue, and reduced front-end leverage when running stock low handlebar positions.
Precision-machined in the USA from 6061-T6 billet aluminum, the 0602-1518 kit installs directly between the top triple clamp and the factory lower handlebar perches.Interlocking spacer blocks allow riders to customize handlebar height from 5 mm up to 20 mm without replacing their stock 1-1/8" (28.6 mm) tapered handlebars or bar clamps. The kit includes matched high-tensile socket-head mounting bolts in two lengths (60 mm and 70 mm) to maintain proper thread engagement across every spacer stack height, along with an 8 mm hex wrench for installation.
Adjustable 5 mm – 20 mm Rise: Interlocking spacer blocks allow custom bar height adjustments up to 20 mm to optimize standing ergonomics and rider leverage.
6061-T6 Billet Aluminum Construction: CNC-machined from aircraft-grade aluminum for high torsional rigidity and zero bar-mount flex under hard impacts.
Interlocking Alignment Bosses: Machined step-and-pocket geometry locks stacked spacers squarely together and into the OEM lower bar perches to prevent twisting.
Preserves OEM Handlebars & Clamps: Installs beneath the stock lower bar perches, retaining full compatibility with factory 1-1/8" (28.6 mm) oversized handlebars and controls.
Dual-Length Hardware Included:Ships with both 60 mm and 70 mm high-tensile M10 mounting bolts so thread engagement matches your selected riser height.
Made in the USA: Engineered and CNC-machined in the United States.
1x Set of CNC-Machined 6061-T6 Billet Aluminum Interlocking Riser Spacers (5 mm to 20 mm stackable configuration)
2x M10 x 60 mm High-Tensile Hex-Socket Mounting Bolts (for 5 mm – 10 mm rise)
2x M10 x 70 mm High-Tensile Hex-Socket Mounting Bolts (for 15 mm – 20 mm rise)
1x 8 mm Hex / Allen Installation Wrench
1x Installation Instruction Sheet
Cast vs. CNC Billet Triple Clamp Warning: Designed specifically for models equipped withOEM cast or forged aluminum triple clamps. DoesNOT fit models factory-equipped withCNC-machined billet triple clamps (including KTM SX/SX-F/XC/XC-F, Husqvarna TC/TX/FC/FX, KTM 300 XC-W Hard Enduro, and Husqvarna TE 300 Pro / Heritage models), which require part number: 0602-1422. Does not fit pre-2024 enduro/dual-sport models or pre-2023 SX / XC models.
Part Number Cross-Reference:Cross-references Enduro Engineering Manufacturer Part Number23-1024
Installation Without Removing Handlebars: You do not need to unbolt your handlebars, grips, or control perches to install this kit.Support the front fender or place a clean shop towel over the fuel tank, then use aT-45 Torx socket from underneath the top triple clamp to remove the two factory bar-mount bolts. Lift the handlebars and lower perches upward as a single assembly, slide the selected riser blocks underneath, and retain the thick factory steel washers to place beneath the heads of the new mounting bolts.
Bolt Length Selection & Threadlocker Protocol (Critical): Match the supplied bolts strictly to your chosen stack height:
5 mm – 10 mm Rise:Use the60 mm socket-head bolts.
15 mm – 20 mm Rise: Stack the 5 mm spacer on top of the 15 mm spacer and use the70 mm socket-head bolts.
Never install the longer 70 mm bolts with a 5 mm or 10 mm spacer—the bolt will bottom out inside the blind threads of the lower bar perch before clamping it tight against the triple clamp.Apply a drop of medium-strength (blue) threadlocker to the bolt threads and torque from underneath using the supplied 8 mm hex key to KTM/Husqvarna factory specification (29.5 lb-ft / 40 Nm).
Cockpit Reach & Steering Angle Geometry: Because the steering head and triple clamps are raked backward at roughly 26 degrees, raising the handlebars vertically along the fork axis also moves the grips slightly rearward toward the rider. If the bars feel too close after raising them 15 mm or 20 mm, rotate the reversible OEM lower bar perches 180 degrees into the forward mounting position on the triple clamp to restore neutral cockpit reach.
Full-Lock Cable & Brake Line Slack Check: Before riding, lift the front wheel off the ground and turn the handlebars smoothly from full left lock to full right lock. Confirm that the front hydraulic brake hose, clutch line, throttle cables (or ride-by-wire harness), and handlebar switch wiring have adequate slack and do not pull tight against the triple clamp or headlight mask.

Part Number:0602-1518
If you have any questions or need help finding what you need for your motorcycle or your next adventure please reach out:
EMAIL US AT tmbrmoto@tmbrmoto.com- OR CALL - 208-254-2044
Our shop is temporarily closed. Check back soon — we'll be back before the next ride.