FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
FREE SHIPPING ON ORDERS $149+
**SOME RESTRICTIONS APPLY
Store Updates
The Supersprox 525 Countershaft (Front) Sprocket (CST-1370-15-2 / CST-1370-16-2) is a case-hardened chromoly steel front drive sprocket engineered for the Honda CRF1000L and CRF1100L Africa Twin adventure motorcycles. Heavy twin-cylinder adventure bikes transmit substantial torque through the final drive over long highway transits and technical off-road terrain. Standard soft-carbon steel sprockets hook and wear prematurely under grit and load, accelerating chain stretch and risking tooth failure in remote backcountry conditions.
Manufactured in Europe from SCM-435 carbon-free case-hardened steel, the CST-1370 series undergoes a specialized carbon-impregnation heat treatment that creates an ultra-hard, low-friction outer wear surface while preserving a ductile, breakage-resistant internal core.Each sprocket is CNC-machined to exact OEM countershaft spline tolerances, fully lightened with radial weight-reduction holes, and machined with self-cleaning root grooves that evacuate mud and sand from beneath the chain rollers.Available in stock 16-tooth (CST-1370-16-2) gearing or 15-tooth (CST-1370-15-2) (-1 tooth) gearing for tighter low-speed off-road control.
SCM-435 Case-Hardened Chromoly Steel:Carbon-impregnated surface layer resists abrasive tooth wear and reduces chain drag, while the refined steel core prevents tooth shearing under shock loads.
Self-Cleaning Mud & Grit Grooves: CNC-machined relief grooves at the base of each tooth evacuate trapped dirt, sand, and mud to prevent chain binding and extend 525 drive chain life.
Radial Lightening Holes:Precision-drilled web cutouts reduce rotating unsprung mass on the countershaft without sacrificing structural rigidity.
15T & 16T Gearing Options: Choose16T (CST-1370-16-2) to maintain factory OEM highway cruising RPM, or drop to15T (CST-1370-15-2) for a ~6.25% gearing reduction that improves technical singletrack modulation and steep hill-climb tractability.
CNC-Machined Spline Fitment: Exact 13-spline internal broaching eliminates countershaft wobble and ensures true chain alignment.
Made in Europe:Engineered and manufactured in Supersprox’s European production facilities to factory rally and enduro team standards.
1x Supersprox 525 Steel Countershaft Front Sprocket in selected tooth count:
15-Tooth Variant:Part #CST-1370-15-2
16-Tooth Variant (OEM Stock Size):Part #CST-1370-16-2
(Note: Reuses OEM Honda countershaft sprocket retaining bolt and washer).
OEM Rubber-Cushion Distinction: The factory Honda front sprocket incorporates molded rubber sound-damping rings on either side of the teeth. The Supersprox-2 series (CST-1370-15-2 /CST-1370-16-2) is an all-steel, radially lightened performance design without rubber damper rings—shedding weight and preventing mud packing in off-road conditions.
Honda DCT Transmission Note: ForDual Clutch Transmission (DCT) Africa Twin models, dropping from the stock 16T to 15T alters wheel-to-engine speed ratios and may trigger shift-point delays or ABS/Traction Control fault codes unless paired with an electronic speedo/gear calibrator. Manual-transmission models accept the 15T swap with no electronic faults.
15-Tooth vs. 16-Tooth Gearing Selection: The Honda Africa Twin leaves the factory with16T front / 42T rear gearing (2.625 final drive ratio). While 16T delivers relaxed 4,000 rpm highway cruising, first and second gears can feel tall in slow, rocky technical terrain or steep loose climbs, forcing excessive clutch slipping. Swapping to the15T (CST-1370-15-2) lowers overall gearing by 6.25%—roughly equivalent to adding 2.5 to 3 teeth on the rear sprocket—giving sharper throttle response in slow singletrack while retaining usable highway cruising speeds. Because the Africa Twin reads vehicle speed from the ABS wheel speed sensors rather than a countershaft sensor, manual-transmission models will continue to display accurate speedometer readings after a 15T swap.
Countershaft Spline Cleaning & Bolt Torque Protocol: When removing the front sprocket cover on the CRF1000L/CRF1100L, clean away accumulated chain lube and trail grit around the countershaft seal and clutch slave cylinder pushrod before pulling the old sprocket. Inspect the OEM countershaft splines for wear and apply a thin film of molybdenum disulfide (moly) paste to the splines before sliding on the new Supersprox sprocket. Reinstall the factory cupped Belleville washer with theconvex ("OUT") side facing outward against the bolt head, apply a drop of medium-strength (blue) threadlocker to the M10 center bolt threads, and torque to Honda’s factory specification of40 lb-ft (54 Nm).
Replace Sprockets and Chain as a Matched Set: A worn, hooked front sprocket accelerates roller and pin wear on a brand-new chain within a few hundred miles, and a stretched chain will rapidly chew through fresh SCM-435 sprocket teeth. Whenever installing a new countershaft sprocket with significant mileage on your drivetrain, inspect the rear sprocket teeth and check chain elongation across 20 links; for maximum service life, replace the front sprocket, rear sprocket, and 525 O/X-ring chain together.
Chain Slack Adjustment After Dropping to 15T: Switching from a 16T to a smaller-diameter 15T front sprocket introduces slightly more vertical chain slack. After torquing the front sprocket bolt, adjust your rear axle blocks to set chain slack to Honda’s specification (35–45 mm / 1.4–1.8 in measured at the midpoint of the lower chain run on the side stand) and verify rear wheel alignment using a Motion Pro Chain Alignment Tool (08-0048).

Part Number: CST-1370
If you have any questions or need help finding what you need for your motorcycle or your next adventure please reach out:
EMAIL US AT tmbrmoto@tmbrmoto.com- OR CALL - 208-254-2044
Our shop is temporarily closed. Check back soon — we'll be back before the next ride.