{"product_id":"motion-pro-pedal-anchor-kit-11-0008","title":"Motion Pro - Pedal Anchor kit","description":"\u003ch1\u003eMotion Pro Pedal Anchor Kit - \"Brake Snake\"\u003c\/h1\u003e\n\u003cp data-path-to-node=\"1\"\u003eThe rear brake pedal on a dirt bike or adventure motorcycle is inherently vulnerable. Protruding from the side of the engine, it is a prime target for deep ruts, hidden rocks, and thick brush. A hard impact can easily bend the pedal outward or snap it off completely—either of which can instantly end a race or leave you stranded miles deep in the backcountry. The Motion Pro Pedal Anchor Kit, commonly known in the off-road community as a \"brake snake,\" is one of the most cost-effective pieces of preventative insurance you can install on your motorcycle.\u003c\/p\u003e\n\u003cp data-path-to-node=\"2\"\u003eThis simple yet highly effective tether system connects the tip of your brake pedal to your motorcycle's frame or engine case. In the event of a crash or a rock strike, the heavy-duty braided stainless steel cable takes the load, preventing the pedal from hyperextending outward. Additionally, it acts as a physical barrier, preventing thick weeds, vines, and trail debris from wedging between the pedal and the clutch cover, which can cause the rear brakes to drag and overheat.\u003c\/p\u003e\n\u003ch4 data-path-to-node=\"3\"\u003eFeatures:\u003c\/h4\u003e\n\u003cul data-path-to-node=\"4\"\u003e\n\u003cli\u003e\n\u003cp data-path-to-node=\"4,0,0\"\u003e\u003cb data-path-to-node=\"4,0,0\" data-index-in-node=\"0\"\u003ePrevents Pedal Damage:\u003c\/b\u003e Stops the brake pedal from bending outward or snapping off during crashes, rock strikes, and deep rut snags.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp data-path-to-node=\"4,1,0\"\u003e\u003cb data-path-to-node=\"4,1,0\" data-index-in-node=\"0\"\u003eDebris Deflection:\u003c\/b\u003e Keeps brush, branches, and heavy mud from packing tightly behind the brake pedal and interfering with brake actuation.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp data-path-to-node=\"4,2,0\"\u003e\u003cb data-path-to-node=\"4,2,0\" data-index-in-node=\"0\"\u003eHeavy-Duty Construction:\u003c\/b\u003e Built from ultra-strong galvanized steel cable that withstands extreme tension without snapping.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp data-path-to-node=\"4,3,0\"\u003e\u003cb data-path-to-node=\"4,3,0\" data-index-in-node=\"0\"\u003eProtective Polyurethane Sheath:\u003c\/b\u003e The cable is wrapped in a thick, clear protective casing to prevent the steel wire from rubbing against and wearing through your engine case or frame paint.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp data-path-to-node=\"4,4,0\"\u003e\u003cb data-path-to-node=\"4,4,0\" data-index-in-node=\"0\"\u003eUniversal Fitment:\u003c\/b\u003e Designed to work on virtually any off-road, dual-sport, or adventure motorcycle. Includes premium aluminum crimps for a secure, custom-length installation.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eFitment:\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eUniversal Fitment\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eFitment Notes:\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli data-path-to-node=\"16\"\u003eThe most common mistake riders make when installing a brake snake is pulling the cable too tight. If the cable has zero slack, it will restrict the downward travel of the brake pedal, severely limiting your braking power. Conversely, if it is too loose, the pedal will bend before the cable catches it.\u003c\/li\u003e\n\u003cli data-path-to-node=\"18,0,0\"\u003e\n\u003cb data-path-to-node=\"18,0,0\" data-index-in-node=\"0\"\u003eMounting Points:\u003c\/b\u003e Loop one end around the lower frame rail or a sturdy engine mount. Attach the other end to the tip of the brake pedal.\u003c\/li\u003e\n\u003cli data-path-to-node=\"18,1,0\"\u003e\n\u003cb data-path-to-node=\"18,1,0\" data-index-in-node=\"0\"\u003eDrilling the Pedal:\u003c\/b\u003e Many aftermarket brake pedals come with a pre-drilled hole for a brake snake. If your OEM pedal does not have one, you will need to drill a small hole (just large enough to pass the bare wire through) near the toothed tip of the pedal.\u003c\/li\u003e\n\u003cli data-path-to-node=\"18,2,0\"\u003e\n\u003cb data-path-to-node=\"18,2,0\" data-index-in-node=\"0\"\u003eSetting the Slack:\u003c\/b\u003e Push your brake pedal down as hard as you would during a panic braking situation. Set the cable length so it is \u003ci data-path-to-node=\"18,2,0\" data-index-in-node=\"131\"\u003ejust\u003c\/i\u003e coming taut at the absolute bottom of the pedal's stroke.\u003c\/li\u003e\n\u003cli data-path-to-node=\"18,3,0\"\u003e\n\u003cb data-path-to-node=\"18,3,0\" data-index-in-node=\"0\"\u003eCrimping:\u003c\/b\u003e Slide the aluminum crimps into place. Use a dedicated wire crimping tool or a heavy pair of vice grips to crush the aluminum sleeves securely. Trim any excess bare wire to prevent it from snagging your boots.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003ca title=\"Shop for Motion Pro tools, parts and accessories at TMBR MOTO. All of your motorcycle maintenance needs in one place.\" href=\"https:\/\/www.tmbrmoto.com\/collections\/motion-pro\"\u003e\u003cimg alt=\"Shop for Motion Pro tools, parts and accessories at TMBR MOTO.\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0622\/5720\/1317\/files\/Motion_Pro_Tools_Parts_and_Accessories_Banner.jpg?v=1780694060\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0622\/5720\/1317\/files\/Made_In_The_USA_24865b83-5069-42c1-b4bc-9e28ee4fe2cb.jpg?v=1719961954\"\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003ePart Number: 11-0008\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"Motion Pro","offers":[{"title":"Default Title","offer_id":47890650071205,"sku":"MP-PDL-ANCR-KIT","price":9.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0622\/5720\/1317\/files\/Motion_Pro_Pedal_Anchor_Kit_11-0008.jpg?v=1780879554","url":"https:\/\/www.tmbrmoto.com\/products\/motion-pro-pedal-anchor-kit-11-0008","provider":"TMBR MOTO","version":"1.0","type":"link"}